DIY Photography: Breadbox Striplight

3

Need a Strip-light, but no budget? Here’s a tutorial on how to make one for less than $20.

You can get a lot fancier with assembly and hardware, but if you’re not going to drive it down a gravel road at high speed, then don’t. You can skip down to see a finished version (maybe see if this is worth the time before starting).

This DIY is not a complete how-to, covering every step. A picture’s worth at least 1000 words, so you’ll have to common-sense your way through much of the process. It’s fairly easy to assemble with a minimum of tools.

Materials:

  • Bread container (they’re $5 at Wal-mart if you don’t find a cheapo buy like mine)
  • Spigot with 1/4" threaded female end
  • (1) 1/4" X 1" hex-head bolt with (1) 1/4" lock washer and (1) 1/4" flat washer (to mount spigot to Strip-light)
  • (4) #8-32 X 3/4" machine screws with (4) nuts and (4) lock washers
  • (8) #8 fender washers (they’re about 3/4" across)
  • Tin foil (the heavy-duty type is easier to handle)
  • Spray glue (or rubber cement). Lighter fluid or charcoal lighter is handy for clean-up)
  • Gaffer tape (duct tape will work, but Heidi might laugh)
  • Sharpie marker
  • Razor/box knife (and maybe band-aids). WARNING: They call ’em “Razor” knives for a reason. Be careful!
  • Drill and 3/16" and 1/4" bits
  • Screwdriver, pliers and a couple of small wrenches
  • Paper towels (for cleanup)
  • Can opener
  • (1) Can of spaghetti sauce
  • (6) Cold bottles of beer hot chocolate cups (12 works better)

Have a beer hot chocolate, and then mark the lid. Mark for your largest flash and leave 1/4" extra all-round.

You can also mark the ‘tab’

After you mark it, cut an H-shaped hole like this (and optionally, cut off the ‘tab’). The dangerous part’s over; have a couple more beers hot chocolates. Here’s how it’ll look:

To illustrate, this is how the flash will fit in the hole. Jam ’er in there! The two flaps in the hole steady the flash and allow for different-sized flash heads.

Now, take the lid and flash off. Line three sides and the top with foil. I sprayed the inside with adhesive and put the foil on, smoothing it as best I could. If you miss a spot, just spray/brush a little more glue and patch over it until all three sides are well-covered. If it looks like hell, don’t sweat it. Your clients will never look inside, and neither will anyone else. The whole outside gets covered with gaffer-tape anyway. If you get glue on the flat/front surface, a little lighter fluid on a rag will clean it up fast. That side shows, and is where the light comes out.

Have another beer hot chocolate (or two) and, if you just can’t wait, you can put the lid and flash on and give it a quick pop. Start low, this thing transmits a lot of light. This is 1/4 power on a Nikon SB-25 at F/10 (I believe at ISO 200). Don’t worry if it looks a little funky, the hot chocolate and glue fumes are probably doing their job.

Put the spigot on. I did step 6 first so you can see the spigot-mounting stuff in a shot. It is easier to mount the spigot now and cover all but the actual spigot in the next step.

WARNING: The can lids are slice-yer-finger sharp! Be careful here!

Remember, beer hot chocolate dulls pain; have another one before and after this step as needed.

a) Open the spaghetti sauce now. Empty the can and save the sauce for later. Keep the top from the can and open the bottom and keep that tin disc too. I put the lids together and pounded them on a piece of wood with a rubber mallet to get the sharp edges flattened. Throw the can carcass away unless you have an iron snoot DIY in mind for later.

b) Drink more beer chocolate.

c) Clamp the two can lids together and drill a 1/4" hole in the middle.

d) Drill 4 – 3/16" equidistant holes about 1.2" from the edge. KEEP THESE CLAMPED TOGETHER UNTIL THE DRILLING IS DONE TO KEEP THE HOLES ALIGNED. MIGHT NEED MORE HOT CHOCOLATE HERE.

e) Put one lid on the outside of the Strip-light and drill through the Strip-light at each hole (1/4" in the center, 3/16" for the others).

f) Put the 1/4" bolt with its lockwasher on through the center of one lid and the stripbox (FROM THE INSIDE). Put the other lid on the bolt outside the Strip-light and LOOSELY screw on the spigot so you can turn the lids and align them in the next step.

g) Align the holes (might require more beer) and put the 4 smaller screws through the lids and the stripbox. There should be a fender washer on the outside and the inside. The screw heads should be on the outside, and the nuts and lockwashers on the inside of the Strip-light.

h) Tighten up EVERYTHING well. You can see what this looks like further down.

The spigot is mounted very near the flash-end so that it will balance well with a flash attached. The purpose of the can lids and fender washers is to distribute force on the spigot across a larger area of the box so it won’t break off when your lightstand falls. IT WILL FALL EVENTUALLY; I PROMISE!

Put the lid on and stick the flash through its hole. Figure out where you need to thread your strap (mine’s a ball-bungee, but you could use elastic or wrap a couple of huge rubber bands around the whole rig) through and drill holes through the box above the protruding lip. Thread the strap through the box and leave it hanging for now.

Cover everything with some gaffer/duct tape. Since my local camera shop gets $22 a roll for this stuff, I’m a little sparing with it. The spigot mount is uncovered below so you can see what the mounting looks like. On my next one, I’ll cover everything but the actual spigot. Have another beer hot chocolate or two.

You can make a couple of gobos (barndoors) from some Coraplast sheet. Some good cardboard or plastic cut from a square kitty-litter bucket will work too. Remember the DIY “gridded snoots” that used Coraplast for the grid?

Cover them with gaffer tape and put the velcro tabs on later when you can line ’em up with the Strip-light. You can also make a small barndoor that goes between the top of the side ones and makes a “box” out of the top. These are about 3" wide, and stick out in front of the flat face of the Strip-light about 2" or so.

Have another brew and mount ‘er up! Here’s what it looks like. The barndoors are laid alongside in one of the pics so you can see them:

On a lightstand

Shot from 15’ away (without barndoors):

Finished product with barndoors alongside:

Make dinner with the spaghetti sauce, have a couple of cold hot ones and relax while you wait for the contracts to roll in. Oh, yeah, you might take a few shots with your Strip-light(s) to see if they actually do lure in a few supermodels.

If you are using a good strap to hold the flash on, you can leave the lid un-taped so you can stuff gobos and other junk (even a flash) inside for transport.

DIY Photography is a place dedicated to photography lovers. DIY Photography aims to share tips, techniques and creative alternatives for photography without breaking your bank account.

Are you in the Do It Yourself mode? Check out some more DIY projects, read more about the DIY Sardina or enter the Do It Yourself Competition. Don’t have a DIY Sardina yet? Get it in the online shop.

written by ilkadj on 2012-08-08 #gear #tutorials #tupperware #diy #tipster #photography #diy-tutorial #striplight #breadbox #spaghetti

3 Comments

  1. buckshot
    buckshot ·

    Wow, you put a lot of effort into this. Congrats!

  2. sixsixty
    sixsixty ·

    This is FANTASTIC! I'll let you know how this turns out when I build mine!

  3. clownshoes
    clownshoes ·

    Awesome mod!

More Interesting Articles

  • Photo of the Day by rickytickitavvi

    written by lomography on 2015-10-28 #news
    Photo of the Day by rickytickitavvi

    For those who are on a tight budget but still want to dress up for Halloween, here's a spooky costume that can be assembled with a few materials.

    2
  • Recap: Film Photography Day 2016

    written by Lomography on 2016-05-02 #news #videos
    Recap: Film Photography Day 2016

    On April 12, analogue fans from all over the world celebrated Film Photography Day! Here's a look back to all the fun that happened. One thing's for sure: Lomographers know how to party!

  • Alternative Processes: Caffenol

    written by Julien Matabuena on 2015-09-11 #tutorials
    Alternative Processes: Caffenol

    We're kick starting a new series on the Magazine where we highlight alternative photography processes, with a focus on modern and less popular ones. Today, we feature one that's often discussed right here in our community: caffenol.

  • Shop News

    Celebrate summer with the Lomo'Instant San Sebastián

    Celebrate summer with the Lomo'Instant San Sebastián

    Walk along the sandy shore, take a dip and splash around, and celebrate summer with the Lomo'Instant San Sebastián! Inspired by the Spanish surf town, this nifty newest edition of the Lomo'Instant is perfect to capture your colorful instant summer snaps!

  • December 16th Advent Offer: Stock Up On Film With Our Festive 3 For 2 Deal! (Online Code: THREE4TWO)

    written by Lomography on 2015-12-16 #news #gear
    December 16th Advent Offer: Stock Up On Film With Our Festive 3 For 2 Deal! (Online Code: THREE4TWO)

    What better way to spread holiday cheer than by capturing it with your trusty camera? We're making it a little bit easier today, because today you can load up on all your favorite Lomography films for less! So stock up and get ready to snap the winter away!

  • Bright Lights with Light Painting Tools

    written by lomographymagazine on 2016-02-26 #news #gear
    Bright Lights with Light Painting Tools

    Creative photography has never been this fun, especially at night. No need to go far for the best source of LED sticks. Lomography has user-friendly and easy-to-use Light Painting Tools to create those coveted night photographs.

  • Tipster: Sizing and Installing Masks in the Lomo'Instant

    written by ahollond on 2015-09-12 #gear #tutorials
    Tipster: Sizing and Installing Masks in the Lomo'Instant

    Seeing cool masked photos on the Lomography site made me want to experiment with the Lomo'Instant. Making masks for the Lomo'Instant is slightly different than that for other Lomo cameras, but the steps in this article should make it easy.

    2
  • Shop News

    Up to 50% off on Lomography Bags!

    Up to 50% off on Lomography Bags!

    Need something to keep your gear safe in and share your pride with the world? An amazing selection of Lomography bags are currently on sale! Don't lose the moment and get your favorite one!

  • Trending Albums of June 2016

    written by lomography on 2016-06-24
    Trending Albums of June 2016

    An album is more than just a collection of photographs. It can accurately tell your tale without the need for words. Take a look at this month's most note-worthy albums and get a hint on how to share your stories through visual organization.

    6
  • DIY Film Developing with One Day on Film

    written by lomographymagazine on 2016-03-07 #videos
    DIY Film Developing with One Day on Film

    Analogue photography alone is tricky business for the newbie, and film development is another skill to master. Learning never stops at just a tutorial or two. Van Dan, a music producer and photographer, gives a comprehensive breakdown of film development for experts and neophytes alike.

  • Trending LomoKino Movies of 2015

    written by lomography on 2015-12-29 #news #videos
    Trending LomoKino Movies of 2015

    Creating a movie, no matter how short it is, requires an extra effort. For it to be coherent, one must stay focused throughout the entire process - from planning the story, shooting the scenes, to editing the clips. We'd like to commend these lomographers for taking an extra step to keep the spirit of analog movie making alive!

  • Shop News

    Explore the New Jupiter 3+

    Explore the New Jupiter 3+

    A resurrection from the zenith of Russian premium optics, get the same elegance and classic compact design as its predecessor. — available in small quantities on a first-come, first-served basis.

  • Through New York City with Markus Hartel and the New Russar+

    written by zonderbar on 2015-09-11 #people
    Through New York City with Markus Hartel and the New Russar+

    New York City-based graphic designer Markus Hartel has a passion for street photography. On one of his last strolls through the city, he captured some scenes on the busy streets with the New Russar+ Lens. Read on to learn about his experience photographing with the Russar+ and get insider info on how it is to be a street photographer in the Big Apple.

    1
  • A Color Remix

    written by lomographymagazine on 2016-02-09 #gear
    A Color Remix

    It's human nature to be restless and imaginative. The real may be interpreted as what one sees or how one sees something. For the daydreamer, a scene from nature transforms into a canvas. Suddenly a field makes room for chemical coloring, all those anachronistic streaks that somehow look right. Or else, those beautiful colors amplified or subdued to their most pictorial shades. All in the world of trial-and-process film photography.

  • A World in a City: NYC Exhibition Recap

    written by lomographynyc on 2016-02-16 #news
    A World in a City: NYC Exhibition Recap

    Expect no less than an exhibit party for the Lomography-reincarnated Jupiter 3+ Art Lens. Only right to celebrate great optical design! Missed the launch? Come, sneak a peek.