This is your last chance to pre-order your Petzval Lens and get the special aperture plates included for free! With estimated delivery in August (or even sooner), don’t miss out on securing your picture perfect portrait lens!

Have an account? Login | New to Lomography? Register | Lab | Current Site:

No more crooked scans with the DigitaLIZA!

Click here to learn about the modification of the standard negative holder to fit the DigitaLIZA in my scanner. Thus, the DigitaLIZA can be aligned in the center for straight scans.

Anyone with a flatbed scanner and the DigitaLIZA knows this problem: The transparency unit is located somewhere in the middle of the scan area, so you can’t align the DigitaLIZA to an edge. The result is that the negatives, after changing to a new film strip, is never in the same place and you must always create a new scanning frame.

The standard negative holder, however, is fixed on my Canoscan 9000 with two small tabs in the scanner:

At some point in the chaos on the desk, I noticed that the 35mm DigitaLIZA is about the size of the inner frame of my medium format holder:

The negative holder is standard, according to the manufacturer it is in stores or on the Internet for 15-20 € ($20-30). I have therefore ordered an additional medium format holder. Since the bracket is made ​​of relatively soft plastic, the inner part cut easily with a sturdy craft knife. Naturally, I had to unhook the folding framework for medium format strips beforehand.

After that I was able to lay on to the mounting DigitaLIZA and draw the cutting edge. With a craft knife, a small bow saw and a nail file, the negative holder was cut out appropriately within 15 minutes. Take care of your fingers when sawing! The modified holder looked then, compared to the untreated part, like this:

The cutout on the left, the original on the right.

Now when I use the DigitaLIZA, I put the modified frames in the scanner and leave it there. During negative changes, I need only take the DigitaLIZA from its new frame, insert a new film strip and put it back in the frame. The negative is always located in the same place in the scanner, centered under the transparency unit. This saves a lot of time and “eye-measurements”…

The next project is now a framework for the DigitaLIZA 120. It is naturally somewhat larger. The system is the same, but then something must be cut out larger.

I hope this helps you a bit when scanning!

written by mike_z and translated by duckduckninja

6 comments

  1. clownshoes

    clownshoes

    Ha yes; Great Canoscan mod

    about 3 years ago · report as spam
  2. nigelk

    nigelk

    Great idea!!

    about 3 years ago · report as spam
  3. _wasabi_

    _wasabi_

    Wow, great idea. Are you happy with this scanner? I'm looking for something to scan 120 and 35mm, and am considering the canoscan 9000f.

    about 3 years ago · report as spam
  4. mike_z

    mike_z

    @ _wasabi_
    Yes, I´m quite happy with my Canoscan. For sure it´s not that fast and powerful like an ususal negative scanner, but it delivers a reasonable quality. You will get the best performance with Silverfast software and 4800dpi setting. According to a test chart scan this results in a real 2100dpi scan, which is quite enough data. The original Canon software is crappy, so look for a bundle...

    about 3 years ago · report as spam
  5. _wasabi_

    _wasabi_

    @ mike_z Thanks for the info, I've gone ahead and ordered one... :)

    about 3 years ago · report as spam
  6. nicx

    nicx

    Awesome tip. i just got this scanner now to see if i can get another scanning mask!

    almost 3 years ago · report as spam

Read this article in another language

The original version of this article is written in: Deutsch.