A Simple Guide to Setting Up Your Own Photographic Darkroom

8

In this simple tutorial our friends over at PhotoTuts+ teach you how to make your own photographic darkroom for developing black & white film!

Written by: Deborah Kanfer

A Simple Guide to Setting Up Your Own Photographic Darkroom

It takes a lot of ambition, interest, and curiosity to have the drive to go back to the traditional roots of photography and get stuck into manual photographic printing and processing. For me, however, I find this to be an utterly rewarding process in my constant exploration of the medium.
In this tutorial, I will go through the basics of what is needed to set up your very own black and white photographic darkroom.

Image Sourced from eHow

Introduction
Manual processing is very fickle in the sense that every element, no matter how minute, can have a profound effect on the final image produced. All variables (i.e. water temperature, exposure duration, etc.) need to be taken into account when producing an image as the slightest variation in these elements can cause a completely different result (sometime rewarding, but sometimes frustrating).
In this tutorial, I will go through the basics of what is needed to set up your very own black and white photographic darkroom. Please keep in mind that what I am about to teach you only covers black and white photographic printing and processing, not colour printing and processing. This is because both consist of entirely different processes of setup and development.

The Process
What happens in a dark room can be divided into two phases: exposure and development. Exposure is the phase where you get your image onto a print by essentially using light to burn the image details onto a piece of photographic paper. However, after photographic paper is exposed, the detail is still invisible to the naked eye and bringing it out takes place in the second phase – development. Manual photography is achieved through chemical reactions and the development phase is where these reactions are initiated and controlled. Think of this phase as an assembly line where different parts or stations complete a unique aspect of the process.

Black and white photographic development is a 4-step process.

Image from Phototuts+

A print needs to be run through developer (to reveal the image detail), stop bath (to stop the effects of the active development), fixer (to finalise or “fix” the image in its current state) and finally rinsed in water (to remove any final traces of chemicals that may further alter your image). Don’t worry if you are confused – I will go into these steps in more detail as the tutorial progresses.

Darkroom Setup
It doesn’t take much to set up your own darkroom. A room that is light tight is essential, because photographic paper and film are light sensitive. If they are prematurely exposed to light your images will be sacrificed to over exposure.

To make sure your room is light tight close the door and turn off the lights to check for any sign of outside light creeping through. If there is, use a towel, black garbage bag or duct tape to block the intruding brightness.

Easy access to running water is a must for chemistry mixing and print washing. This is because you will need to change your rinsing water frequently to avoid any contamination of your paper or chemicals, as the fixer that is washed off in the final tray can become slightly concentrated to the point of ruining your freshly developed images.

The materials that you will need for your dark room are as follows:

Chemistry Trays

Depending on the dimensions of the images you are wanting to print, at least four photographic chemistry trays will be needed. Each tray will contain a different chemical to aid in the development process.

Photographic Safelight

Image from Phototuts+

The safelight is used in the darkroom when handling unexposed or undeveloped black and white images and photographic paper. It creates either a brown or red glow so that you are able to do your thing in the darkroom and still be able to see.

Image from Phototuts+

If you are new to this, it may take a little bit of time for your eyes to adjust. The safe light can be put in any lamp and should be placed somewhere that is easily reachable.

Tongs
Thirdly, you will need four tongs for each tray to be able to turn over your prints and move them from tray to tray. It is best to avoid your skin coming into contact with the chemicals to prevent any future health problems.

Photographic Enlarger
Finally you will want to consider getting a photographic enlarger.

Image from Phototuts+

This device is used for creating an enlarged image from your negatives, to be exposed to your desired size onto photographic paper. If you are able to get a hold of one for an affordable price, by all means grab it. If not, it’s not the end of the world. Having a photographic enlarger is a plus but is not essential for printing and exposing images. It is still possible to create visually appealing images without an enlarger (see our forthcoming articles on photograms and contact printing).
The chemicals you will need are black and white paper developer, stop bath, and fixer.

Images sourced from First Call Photographic, niobo, and HARMAN express.

The paper developer is responsible for developing the image on the exposed paper. While in the developer, you are able to see the image slowly emerge from a blank piece of paper. It’s quite amazing to watch.

Stop bath is a chemical solution responsible for bringing the developing of the image to a halt. If the image stays in developer for too long, the image can get too dark to the point of blackness thus stop is responsible for ‘stopping’ and rinsing the image from developer.
There are several choices for stop bath. One option is to buy acetic acid which is like a form of concentrated vinegar.

Image Sourced from John Penny Restoration Ltd

For a cheaper option purchase a jug of pickling vinegar at your local grocer – about 1/8 of a cup mixed with approximately 950ml of water should do the job.

Image Sourced from eHow

As a final option, you could always purchase a premixed bottle of stop bath, which is usually very affordable.
Lastly, fixer, which is essential to the developing process as it “fixes” your image in it’s final state, allowing the image to be exposed to light as a finished product. If the image is exposed to light without fixer, even after the developing and stopping process, the image can still get fogged or turn completely black. You can purchase fixer at any photographic specialty store. Please refer to the label for solution mixing ratios and measurements.

Get yourself three large glass jars to store your chemistry in after you have completed your printing session, as the solutions can be stored and reused on several sessions.

Last, but most certainly not least is black and white photographic paper (also available at any photographic specialty store or online).

Image Sourced from Ilford Photo

It comes in a variety of sizes and brands, and you also have the option of purchasing it in warm tone for sepia-style colouring (an old style photo look, with a brown-like tint).

Make sure to mark the trays and tongs according to which chemicals they were used with, as you don’t want to contaminate your chemistry or paper.

Image from Phototuts+
Image from Phototuts+
Image from Phototuts+

If contamination does occur, your paper will get brown or yellow blotches similar to the following:

Image from Phototuts+

These are certainly not visually pleasing, and pose the risk of compromising image longevity. The order to place your chemistry trays is as follows; developer, stop, fix and rinse. Some people like to have a fifth tray for either a second stop tray, or a second fixing tray. This is really a matter of personal preference and neither are essential.

Locating Equipment
Most, if not all darkroom equipment can be found at a photographic specialty store. Since digital photography has taken the world by storm, you may find it a little challenging to find what you are looking for, however, there is no secret as to where to find everything you need.

I would always give Goodwill, Salvation Army, eBay or Craigslist a shot. You will be surprised at how people are literally giving away their equipment. As for photographic chemistry and paper, again, any photographic specialty store should have what you are looking for. For solution mixing utensils, all you will need are two funnels (one marked for developer and one marked for fixer), a water jug with measurements on the side (strictly used only for water), and three measuring beakers for measuring the chemicals. These are best to have in large sizes that go up to one litre.

Image Sourced from Rapid

Finally, you will need a timer so that you can keep track of your developing time of each image in each tray. Now you’re good to go!

Equipment Placement
If, like me, you have successfully managed to turn your tiny bathroom into a fully functioning darkroom, the best thing would be to place the three chemistry trays in your bath tub. Otherwise, somewhere fairly spacious and flat will suffice. Make sure to keep your photographic paper and not-yet-developed images in a dry area, at a distance from your chemistry trays. The safelight should be placed in an area that is easily accessible and dry, and the same goes for the enlarger.

Common Problems and Obstacles
If you are unable to find a room that has running water, don’t worry. As long as you do have access to running water within a close proximity of your darkroom, then it is still very possible to continue with your printing endeavors.

Remember to frequently change your rinsing tray water and always wash your hands if you come into contact with the chemistry. This will prevent chemistry contamination marks on your prints, as well as the prevention of any future health problems. Keep everything as clean and dry as possible and wash your trays and tongs thoroughly after every printing session.

Experiment, have fun, and soon you will begin to establish your own rhythm and order in darkroom developing. You’ll be hooked in no time!

Phototuts+ is a source of learning on all aspects of photography. If you love photography, you will find a treasure trove of useful advice at Phototuts+. Also, keep an eye out on Phototuts+ as they will be featuring one Lomography tipster a month, yours could be the lucky one!

written by jesuisz on 2011-07-22 in #gear #tipster

8 Comments

  1. laurasulilly
    laurasulilly ·

    I have my own darkroom, too (where I also do Holga prints), and I love love LOVE it, although I only set it up a couple of weeks ago!

  2. kiteflyin
    kiteflyin ·

    I'm really bad at watching the clock, but it is really fun (and a bit frustrating) to make your own prints. I wish I had my own setup here at home though.

  3. lisabegusch
    lisabegusch ·

    I hope I can try this sometime soon!
    I guess however that you have to get your negatives developed, right? and then you can print them as you described?

  4. lisabegusch
    lisabegusch ·

    Do you know instructions anywhere on color development/printing? :)

  5. deedeet
    deedeet ·

    thx for the tips man!!!

  6. angelhaken
    angelhaken ·

    citrus based stop bath is unexpensive - CITRIN (Citrostop) from Rollei for example it avoids disturbing and breathing burdening emissions. and it is less risky :). Most of them have an color based indicator that shows how "fresh" the stop-bath is thats the only thing i would add. .. great tutorial :) ..

  7. sought
    sought ·

    It's great details, but just I'm not willing to try it out for now, since I'm very new to lomography. I think i'll have them developed to see what I've been doing. plus, why does everyone keep calling the film negative, what I have is pure black roll!!!!! +_+'''

  8. sw
    sw ·

    I think you're leaving out one of the most important parts: Film tanks, reels, leader fetchers, and D-76. Because you'll already have the main chemicals it makes more sense to develop both the roll of film as well as your prints in the darkroom. It would only cost about another $50.

More Interesting Articles

  • How to Adjust the Settings of the Diana F+

    written by chooolss on 2014-05-04 in #lifestyle
    How to Adjust the Settings of the Diana F+

    Make the most out of your Diana F+ by learning how to properly fiddle with its settings. Let our short video tutorial, featuring the Diana F+ Love Letters, teach you how!

  • Reviews on Rewind: Lomography Earl Grey B&W 100 ISO 35mm

    written by chooolss on 2014-10-29 in #reviews
    Reviews on Rewind: Lomography Earl Grey B&W 100 ISO 35mm

    Classy, moody photographs in monochrome and with fine grain - what more could you ask for from one of Lomography's very own black and white emulsion for standard 35mm cameras, the Earl Grey? Find out how this film fared among six of our community members in this Reviews on Rewind installment!

  • Fresh from My Darkroom: Yoga for Africa!

    written by sirio174 on 2014-06-16 in #lifestyle
    Fresh from My Darkroom: Yoga for Africa!

    Last Sunday, a great yoga event was held in Cernobbio, a small tourist town near the city of Como. Local association Breathe Como made a performance of power yoga exercises to raise funds for Africa. I developed the film a few days ago, and today I'll show the photos to you! I call this "Fresh From My Darkroom" because I developed the black and white films by myself! Take a look!

  • Shop News

    Wear lomo-love on your skin

    Wear lomo-love on your skin

    You’ve shouted your analogue love from the rooftops and worn your heart on your sleeve – Now it’s time to take it to the next level and wear it on your skin! Our new Lomography Tattoos are fun, easy to apply and come in five designs.

  • Finding Humanity in the Streets with Soomin Yim

    written by chooolss on 2014-11-12 in #lifestyle
    Finding Humanity in the Streets with Soomin Yim

    Stop bath is a type of chemical used in the darkroom for processing black and white film, aptly named as such because it halts the development of the images. In this case, stop bath is also part of the title that Korean analogue street photographer <b><a href="http://instagram.com/sooeatsyourstreetforbreakfast">Soomin Yim</a></b> has given her body of work, "Stop Bath the City," to represent the forgotten faces of people in the city amid rapid modernization, captured and immortalized on black and white film.

  • December 9th Advent Offer: Save 10% On Film Today! (Online Code: FILMFANTASY10)

    written by jacobs on 2014-12-09 in #news
    December 9th Advent Offer: Save 10% On Film Today!  (Online Code: FILMFANTASY10)

    We've got another great opportunity for you to load up on all your favorite films! Today's Advent deal is 10% off of all our films! Keep your holidays classy with one of our awesome black and white films or get creative with one of our Redscale films. Whatever you choose will be a great way to document all the upcoming fesitivities!

  • Roundup: Film Photography Day 2014

    written by shhquiet on 2014-06-03 in #news
    Roundup: Film Photography Day 2014

    Did you miss this year's Film Photography Day celebration? Here's a recap of all the events that happened in April, in honor of our love for analogue photography. Of course, remember that you can always make any day a Film Photography Day if you wish; just gather your friends and organize a LomoMatrix in your area! For inspiration, check out what Lomography Gallery Stores and Lomography Embassy Stores from all over the world came up with.

    3
  • Shop News

    Build your own analog SLR Camera!

    Build your own analog SLR Camera!

    With a list of fine accessories it´s not only fun to build but also great to shoot with! Check out the enhanced, flash compatible version now!

  • Twosday Tuesday: Drive

    written by cheeo on 2014-11-04 in #lifestyle
    Twosday Tuesday: Drive

    This instalment of Twosday Tuedsay will teach you how to make ordinary car rides pop with a little help from your panoramic snapper.

  • Create your very own DIY film clips for your lab developing!

    written by cheeo on 2014-04-01 in #gear #tipster
    Create your very own DIY film clips for your lab developing!

    The dark room is where the magic happens when it comes to developiong. And if you’re doing your own developing, you’re going to like this quick DIY film clip!

    1
  • On Using Color Filters to Tweak Hues in Black and White Photography

    written by chooolss on 2014-04-09 in #lifestyle
    On Using Color Filters to Tweak Hues in Black and White Photography

    While it might sound unusual for some right off the bat, black and white film photographers do use color filters to experiment with their shots without ever needing to do some post-processing. How to do that and which filters to use to capture specific scenes? Take a look at this short instructional YouTube video clip by LZ Film Productions!

  • Shop News

    Zap up your Diana F+ with a Crisp Glass Lens!

    Zap up your Diana F+ with a Crisp Glass Lens!

    Thought you can’t get sharp photos with the Diana F+? Think again! With the Diana+ 75mm Premium Glass Lens, you can shoot crisp and clear images with the signature dreamy appeal of the Diana. With our Adaptors you can even make it work on your Nikon & Canon dSLR!

  • Celebrate Black Friday with 30 Beautiful Black & White Photos from the LC-A+

    written by jacobs on 2014-11-27 in #lifestyle
    Celebrate Black Friday with 30 Beautiful Black & White Photos from the LC-A+

    Do you know the best way to celebrate the biggest shopping day of the year? Stay at home and marvel at these gorgeous black and white photos from the legendary LC-A+! There's no reason to stand in line for hours either, when you can get incredible deals here at Lomography without ever leaving the comfort and warmth of your own home. Check out these radiant shots from the LC-A+ and then head over to the Online Shop to save a fantastic 30% on this incredible camera and more!

  • December 13th Advent Offer: Take Advantage of our Festive 3 For 2 Film Deals! (Online Code: 3FOR2HOLIDAYFILM)

    written by jacobs on 2014-12-13 in #news
    December 13th Advent Offer: Take Advantage of our Festive 3 For 2 Film Deals!  (Online Code: 3FOR2HOLIDAYFILM)

    Have you been waiting for a good time to load up on films for all your treasured analogue cameras? The time has come with our stunning Advent deal of the day! With our sweet film packs, we make it easy to cache away enough to last the fun and festive parties coming up. Start stashing now by heading over to our Online Shop!

  • December 14th Advent Offer: Take Advantage of our Festive 3 For 2 Film Deals (Online Code: 3FOR2HOLIDAYFILM)

    written by jacobs on 2014-12-14 in #news
    December 14th Advent Offer: Take Advantage of our Festive 3 For 2 Film Deals  (Online Code: 3FOR2HOLIDAYFILM)

    Seeing that we love to spread the cheer around here, we're giving you another chance to load up on our awesome film with today's Advent deal! Choose a classy black and white film, like our Lady Grey, or get creative and colorful with one of our Redscale films. We're certain that no matter what you choose, you'll have a great time making memories with tons of lovely analogue photos this year!